解决方案查找器

1SP0340V2M0-FZ1200R45HL3

Single-Channel SCALE-2 Plug-and-Play for 4.5kV IGBTs, Direct Paralleling Supported by Master/Slave Drivers

應用
產品規格型錄
下載 PDF 檢視 PDF
產品詳情

The new 1SP0340 SCALE-2 Plug-and-Play driver is specifically designed for the reliable and safe driving of 130 x 140 mm and 190 x 140 mm IGBT modules with 6000 V isolation voltage and 4.5 kV blocking voltage. It is optimized for high-reliability applications in the rail industry. 

The driver concept relies on a master/slave principle that enables parallel-connected IGBT modules to be operated safely. The master (1SP0340V) can be used as a stand-alone driver without slave to drive a single IGBT module, or with up to three slaves (1SP0340D) to drive up to four parallel-connected IGBT modules.
The master is equipped with a fiber-optic interface and global fault management. In master/slave configurations, the slaves are connected to the master via a bus cable which distributes the common command signal and the secondary-side supply voltages from the DC/DC converter. 

The 1SP0340 driver is based on the highly-integrated SCALE-2 chipset which enables high-performance, complete and extremely-compact single-channel IGBT drivers. 

The SCALE-2 chipset also reduces the component count by 80% when compared to conventional solutions, thus significantly increasing reliability and reducing costs.
1SP0340 drivers are equipped with Dynamic Advanced Active Clamping (DA2C), short-circuit protection, regulated turn-on gate driving voltage and supply-voltage-monitoring. 

Tightly-matched driver versions are available for all mechanically-compatible IGBT modules. Plug-and-play capability enables immediate operation after mounting, and the user needs to invest no effort adjusting or designing-in the driver for a specific application.

Fiber-Optic Interface Options
Fiber-optic links are used to electrically isolate the command and status-feedback signals.

For details, please check the product documentation.

Power supply and electrical isolation

In contrast to other SCALE-2 plug-and-play drivers, the 1SP0340 driver is modular, so the driver card and power supply (ISO5125I DC/DC converter) are two separate units. This means that any driver that has been developed to match a specific IGBT module can be used for any required isolation specification. Only the separate power supply (ISO5125I) must be selected to match the specific application. A further benefit is that drivers for 4.5 kV IGBTs can be implemented in 2-level, 3-level and multi-level inverter topologies. 

The driver is mounted directly onto the IGBT module using three screws. The separate power supply unit is attached close by the IGBT. For parallel-connected drivers, only one power supply is needed per switch.

產品規格
產品規格
支持的模組 FZ1200R45HL3
最大開關頻率 3.50 kHz
IGBT電壓等級 4500 V
技術 SCALE-2
輸出功率/通道 - 最大 2.80 W
接口類型 Fiber Optic
IGBT製造商 Infineon
通道數 1
柵極峰值電流 (最大) +35 A
產品類別 Board
Product Sub-Type PnP Driver
支持的模組種類 IGBT
主/外圍 Main
支持的拓撲
2-level Voltage Source
3-level NP-Clamped - Type 1
3-level NP-Clamped - Type 2
Multi-Level NP-Clamped
並行支持?
保護功能
Dynamic Adv Active Clamping
Over-voltage
Short Circuit
UVLO(Sec-side)
保形塗層?
驅動模式 Direct-Independent
IGBT的連接類型 Direct
電源電壓 (典型) 25.00 V
柵極導通電壓 +15.00 V
柵極關斷電壓 --10.00 V
Voltage - DC Link Off state (60s) 3550.00 V
時間 - 輸出上升 10.00 ns
時間 - 輸出下降 25.00 ns
Gate Boosting?
Gate Peak Current (Min) -35