์†”๋ฃจ์…˜ ์ฐพ๊ธฐ ๊ธฐ์ˆ  ์ง€์›

1SP0340D2S0-CM1200HC-90RA

Single-Channel SCALE-2 Plug-and-Play for 4.5kV IGBTs, Direct Paralleling Supported by Master/Slave Drivers

์• ํ”Œ๋ฆฌ์ผ€์ด์…˜
๋ฐ์ดํ„ฐ ์‹œํŠธ
PDF ๋‹ค์šด๋กœ๋“œ PDF ๋ณด๊ธฐ

์ œํ’ˆ ์ƒ์„ธ ์ •๋ณด

The new 1SP0340 SCALE-2 Plug-and-Play driver is specifically designed for the reliable and safe driving of 130 x 140 mm and 190 x 140 mm IGBT modules with 6000 V isolation voltage and 4.5 kV blocking voltage. It is optimized for high-reliability applications in the rail industry. 

The driver concept relies on a master/slave principle that enables parallel-connected IGBT modules to be operated safely. The master (1SP0340V) can be used as a stand-alone driver without slave to drive a single IGBT module, or with up to three slaves (1SP0340D) to drive up to four parallel-connected IGBT modules.
The master is equipped with a fiber-optic interface and global fault management. In master/slave configurations, the slaves are connected to the master via a bus cable which distributes the common command signal and the secondary-side supply voltages from the DC/DC converter. 

The 1SP0340 driver is based on the highly-integrated SCALE-2 chipset which enables high-performance, complete and extremely-compact single-channel IGBT drivers. 

The SCALE-2 chipset also reduces the component count by 80% when compared to conventional solutions, thus significantly increasing reliability and reducing costs.
1SP0340 drivers are equipped with Dynamic Advanced Active Clamping (DA2C), short-circuit protection, regulated turn-on gate driving voltage and supply-voltage-monitoring. 

Tightly-matched driver versions are available for all mechanically-compatible IGBT modules. Plug-and-play capability enables immediate operation after mounting, and the user needs to invest no effort adjusting or designing-in the driver for a specific application.

Fiber-Optic Interface Options
Fiber-optic links are used to electrically isolate the command and status-feedback signals.

For details, please check the product documentation.

Power supply and electrical isolation

In contrast to other SCALE-2 plug-and-play drivers, the 1SP0340 driver is modular, so the driver card and power supply (ISO5125I DC/DC converter) are two separate units. This means that any driver that has been developed to match a specific IGBT module can be used for any required isolation specification. Only the separate power supply (ISO5125I) must be selected to match the specific application. A further benefit is that drivers for 4.5 kV IGBTs can be implemented in 2-level, 3-level and multi-level inverter topologies. 

The driver is mounted directly onto the IGBT module using three screws. The separate power supply unit is attached close by the IGBT. For parallel-connected drivers, only one power supply is needed per switch.

๋ช…์„ธ์„œ

๋ช…์„ธ์„œ
์ง€์›๋˜๋Š” ๋ชจ๋“ˆ CM1200HC-90RA
์ตœ๋Œ€ ์Šค์œ„์นญ ์ฃผํŒŒ์ˆ˜ 8.70 kHz
IGBT ์ „์•• ๋“ฑ๊ธ‰ 4500 V
๊ธฐ์ˆ  SCALE-2
์ถœ๋ ฅ ์ „๋ ฅ / ์ฑ„๋„-์ตœ๋Œ€ 2.80 W
์ธํ„ฐํŽ˜์ด์Šค ์œ ํ˜• Electrical
IGBT ์ œ์กฐ์—…์ฒด Mitsubishi/Powerex
์ฑ„๋„ ์ˆ˜ 1
๊ฒŒ์ดํŠธ ํ”ผํฌ ์ „๋ฅ˜ (์ตœ๋Œ€) +35 A
์ƒํ’ˆ ์œ ํ˜• Board
Product Sub-Type PnP Driver
์ง€์›๋˜๋Š” ๋ชจ๋“ˆ ์œ ํ˜• IGBT
๋ฉ”์ธ / ์ฃผ๋ณ€ Peripheral
์ง€์›๋˜๋Š” ํ† ํด๋กœ์ง€
2-level Voltage Source
3-level NP-Clamped - Type 1
3-level NP-Clamped - Type 2
Multi-Level NP-Clamped
๋ณดํ˜ธ ๊ธฐ๋Šฅ
Dynamic Adv Active Clamping
Over-voltage
UVLO(Sec-side)
๋“œ๋ผ์ด๋ธŒ ๋ชจ๋“œ Direct-Independent
IGBT์— ๋Œ€ํ•œ ์—ฐ๊ฒฐ ์œ ํ˜• Direct
๋…ผ๋ฆฌ ์ž…๋ ฅ ์ „์•• 15
๊ณต๊ธ‰ ์ „์•• (์ผ๋ฐ˜) 25.00 V
๊ฒŒ์ดํŠธ ํ„ด์˜จ ์ „์•• +15.00 V
๊ฒŒ์ดํŠธ ํ„ด ์˜คํ”„ ์ „์•• --10.00 V
์ „์•• - DC ๋งํฌ ๊บผ์ง ์ƒํƒœ, 60 ์ดˆ 3550.00 V
์‹œ๊ฐ„ - ์ถœ๋ ฅ ์ƒ์Šน 10.00 ns
์‹œ๊ฐ„ - ์ถœ๋ ฅ ํ•˜๋ฝ 25.00 ns
๊ฒŒ์ดํŠธ ํ”ผํฌ ์ „๋ฅ˜ (์ตœ์†Œ) -35